It28f no powe to dash and no movement

Hello. We have a cat it28f loader. Loader was moving fine then all of a sudden the there was not power to the dash and no movement in the transmission. Now the loader starts fine but no power to the dash. I’m assuming the I lost power to the ecm. I’m hoping somebody can give me some hint as to where to look or what to check. Thanks in advance.

A serial number might get you a wiring diagram so you could at least have a road map to follow where the power starts and where it stops. As it starts at least that would seem to indicate the disconnect switch and some of the wiring is functional.

Any update on this? I have the same exact scenario going on. No forward or reverse and no dash lights.

4 years later and no reply from the OP. If you want an electrical schematic the first thing you have to provide is a Serial Number in order to identify the correct one.

When you get the schematic look for the main cab relay. It is responsible for cab supply power. It is energized by the key switch.

I realize this is an old post but did anyone on this thread figure out their issue before I start digging? Same exact issue with my it18f. Thank you

It’s was the power box in in the engine compartment. Connections were green molded.

Thomas Brooks said: I realize this is an old post but did anyone on this thread figure out their issue before I start digging? Same exact issue with my it18f. Click to expand... If you would like an electrical schematic for your machine then please post a serial number.

Nige said: If you would like an electrical schematic for your machine then please post a serial number. Click to expand... I'll have to get the serial number once I get to the machine. Thank you!

4digger said: It’s was the power box in in the engine compartment. Connections were green molded. Click to expand... Thank you sir. I'm trying to remember before the engine compartment of the top of my head. I'll be going to the site its at tomorrow to start fixing hopefully. Do you mean the box with a few fuses in it on the passenger side by the engine? Or do you recall the location at all? Thank you very much for any help. Just trying to be prepared before I get there. Thank you!

Thomas Brooks said: I'll have to get the serial number once I get to the machine. Thank you! Click to expand... The options are either 5EJxxxxx or 6ZFxxxxx. Actually when I checked just now they both use the same electrical schematic. Check your message inbox.

hello I have an IT18F with no dash and no back and forth issue when its cold out it does start and once it runs for a while the dash will get power and the loader moves this winter we now have no start,dash nothing there is power to the key switch could we get a drawing PDF please and perhaps the location of the power box that was green

4digger said: It’s was the power box in in the engine compartment. Connections were green molded. Click to expand... hello is this power box the one to the front and right of the motor with the small door with the fuses in it? before I start tearing apart this loader in the freezing cold....could you direct me please

Welcome to the forum. Can you start by posting a machine Serial Number please. Until we know exactly what you have it makes it hard to offer advice.

Nige said: Welcome to the forum. Can you start by posting a machine Serial Number please. Until we know exactly what you have it makes it hard to offer advice. Click to expand... thanks i will be back at the loader tomorrow

Nige said: Welcome to the forum. Can you start by posting a machine Serial Number please. Until we know exactly what you have it makes it hard to offer advice. Click to expand... good morning serial # 97z00604 6rx00521 the plate is very beat up I hope this is correct

Nige said: Welcome to the forum. Can you start by posting a machine Serial Number please. Until we know exactly what you have it makes it hard to offer advice. Click to expand... sorry fingers are faster then my brain looked on internet serial # is 6rx00521

Nige said: Welcome to the forum. Can you start by posting a machine Serial Number please. Until we know exactly what you have it makes it hard to offer advice. Click to expand... oh my lord your going to kick me out on my first day.......mach ser# 97z00604 engine ser # 6rx00521

It’s cold out, called brain freeze. lol

The two numbers you gave are the engine and the transmission Serial Numbers, but no matter. The machine S/N will either start with 5EJ or 6ZF. Either way both models use the same electrical schematic, so check your message inbox. I'm going to be a bit tied up today but if you have any questions hopefully someone else can assist.