New Terex TS24D

I can't believe this. Brand new for 22 years old. Never seen a yard of dirt. Only damage I see is heat damage to the cab upholstery from the Mexico heat. Last year of production. https://www.ironplanet.com/for-sale...00,c|5,m|Terex,sm|0&rr=0.2&hitprm=&pnLink=yes Interesting to see what it brings.

Look a little closer, the router bits are wore out both sides and the cutting edges are broke. Looks like a bunch of welds on the hitch are redone. Bob

I had seen the broken cutting edge, slight scratches on the tire tread face. Still very low hours.

i wonder if it was a demo unit?

56wrench said: i wonder if it was a demo unit? Click to expand... It's a Ritchie overhaul with new tires. Bob

probably. it looks like one of their better overhauls

The draft arm looks like was replaced.

it like a low hour machine, the bush blocks and the bail and hook dont show signs of much wear and the pedals dont show much wear

Questionable wizard said: I can't believe this. Brand new for 22 years old. Never seen a yard of dirt. Only damage I see is heat damage to the cab upholstery from the Mexico heat. Last year of production. https://www.ironplanet.com/for-sale/Scrapers-1999-Terex-TS24D-Motor-Scraper-México/4834397?h=5000,c|5,m|Terex,sm|0&rr=0.2&hitprm=&pnLink=yes Interesting to see what it brings. Click to expand... I don’t think it’s a Ritchie overhaul, looks to be very low hours, I would bet less than 500. I’ve only ever seen two or three 24Ds on the internet, I would like to know how many were built. It will be interesting to see what it brings, hopefully whoever gets it will take care of it. I think the 24B, C, & D were a really good design and I have never understood why Terex didn’t build the TS-14s using a similar design, especially the suspension axle. I think they would still be in the scraper business today had they done that.

traxcavator said: I don’t think it’s a Ritchie overhaul, looks to be very low hours, I would bet less than 500. I’ve only ever seen two or three 24Ds on the internet, I would like to know how many were built. It will be interesting to see what it brings, hopefully whoever gets it will take care of it. I think the 24B, C, & D were a really good design and I have never understood why Terex didn’t build the TS-14s using a similar design, especially the suspension axle. I think they would still be in the scraper business today had they done that. Click to expand... I agree with a suspended front axle. I also wish they would have incorporated the push out ejector on the 14s. Wet material likes to stick in the roll out ejector. Then you have to spend time with an excavator digging them out. Not sure if you could hold a poly truck bed liner in the roll out ejector.

I've seen a few items come from that area. Someone has a hobby of fixing up old equipment and making it look new. I've seen a few tractors and scrapers come out of there at the auction. I do like this scraper and would love to have it. Last I saw it was at 42k.

Questionable wizard said: I agree with a suspended front axle. I also wish they would have incorporated the push out ejector on the 14s. Wet material likes to stick in the roll out ejector. Click to expand... I never had much trouble with it sticking to the ejector (at least not a significant amount) but I believe I did see some 14Bs for sale a few years ago that had some type of liner on the ejector and I thought it was a good idea. I think I have also seen a couple that had the ejector heated off of the rear exhaust. The push out ejection would have made the 14s easier to dump and control the spread. If you are working in sticky clay soils with the units that have cable aprons, the cable needed to be short enough that you could get the apron up high so the load didn’t hang up on the lower lip of the apron. You also had to be careful not to eject all at once, you had to raise the ejector in small increments (sometimes rocking it up and down) until the higher part of the load fell off the top. I have seen many people get frustrated and abuse these machines because they didn’t know how to dump it. The ts-18s had roll out ejection also, but it had the apron like the 24s and 14Gs, the heavy clays didn’t hang up as long you got the apron opened up high enough. I never used any 14Gs in wet clay so I’m not sure if they performed similar to the 18s or not.

traxcavator said: I never had much trouble with it sticking to the ejector (at least not a significant amount) but I believe I did see some 14Bs for sale a few years ago that had some type of liner on the ejector and I thought it was a good idea. I think I have also seen a couple that had the ejector heated off of the rear exhaust. The push out ejection would have made the 14s easier to dump and control the spread. If you are working in sticky clay soils with the units that have cable aprons, the cable needed to be short enough that you could get the apron up high so the load didn’t hang up on the lower lip of the apron. You also had to be careful not to eject all at once, you had to raise the ejector in small increments (sometimes rocking it up and down) until the higher part of the load fell off the top. I have seen many people get frustrated and abuse these machines because they didn’t know how to dump it. The ts-18s had roll out ejection also, but it had the apron like the 24s and 14Gs, the heavy clays didn’t hang up as long you got the apron opened up high enough. I never used any 14Gs in wet clay so I’m not sure if they performed similar to the 18s or not. Click to expand... The 14Gs are kind of a like the Bs and Cs that you would raise the ejector and the wet clump would stick until the ejector was high enough. Then it would roll forward and pack against the cutting edge sliding on the ground. Raise the cutting edge higher and you could get it to shear off or roll under in ugly chunks.

It brought more than I thought it would. I wonder where it’s new home is going to be?

Hello is there somebody who knows what transmission models has been used in the Terex TTS 14 - Twin Bowl Scraper? Regards Sjaak Bos

Sjaak Bos said: Hello is there somebody who knows what transmission models has been used in the Terex TTS 14 - Twin Bowl Scraper? Regards Sjaak Bos Click to expand... Someone correct me if I’m wrong, but I think the TTS-14 used Allison CLT 3461 just like the standard TS-14.

Hey guys, just stumbled onto this thread. Myself and some family own a grading company in Kansas and we bought this scraper. We typically run it five days a week and have since we bought it along with several more that we have. We know our way around a scraper, and this machine was never used until we bought it. Plastic was still on the seat and the factory paint on the bottom of the pan wasn’t scratched. They made 2 D models. We have one and we heard the other is sitting in Canada. Never thought I’d run a brand new scraper, but this machine is incredible. There’s nothing else like a new 24.

HauptRob said: Hey guys, just stumbled onto this thread. Myself and some family own a grading company in Kansas and we bought this scraper. We typically run it five days a week and have since we bought it along with several more that we have. We know our way around a scraper, and this machine was never used until we bought it. Plastic was still on the seat and the factory paint on the bottom of the pan wasn’t scratched. They made 2 D models. We have one and we heard the other is sitting in Canada. Never thought I’d run a brand new scraper, but this machine is incredible. There’s nothing else like a new 24. Click to expand... These are old pictures but I can try and get some of it Monday, if my little brother can slow down enough for a picture haha.

I’d definitely like to see more pics of this please. I’m fond of 24’s

I’ll do that. It’s not as pretty anymore the white paint doesn’t age very well. There’s a video of it push pulling on our Facebook page Haupt Construction Company.